Skip to main content

PAINT COLORS

Paint Colors:


Ceiling, Trim, Doors: SW Snowbound in Semi-gloss
Walls: SW Snowbound in Eggshell

Powder Room:
SW Urbane Bronze

Music Room:
Vertical Shiplap: Tricorn Black

Front and Back Doors:
BM Onyx

Exterior Brick:
BM White Dove

Kitchen Cabinets:
Custom paint color from SW. Here is a picture of the label.


Bathroom vanities:
50/50 mix of pickled oak and weathered oak on Basswood.

Comments

Popular posts from this blog

$40 Sofa Table

Hi! My sweet children kept jumping over the couch so I needed to do something about the madness!  I decided to build an inexpensive sofa table to attempt to minimize the jumping. Will it work? It's a mystery :) Let's get started! As always, use caution when building, wear safety gear and re-read instructions multiple times. This plan is for entertainment purposes only. Supplies: 3-2x12x8 1-package of 2-1/2" pocket hole screws Finishing supplies: stain, paint, seal Tools: Miter saw Drill Pockethole Jig Table saw (optional) Planer (optional) Step 1: (optional) using a table saw rip 1/8" off each side of the 2x12x8 board. Run boards thru a planer if you have one. Step 2: Using a miter saw cut- 4 @ 28" 1 @ 38" 1 @ 68" Step 3: Build the legs. Drill 1-1/2" pocket holes on boards 1 & 2. Mark the 1/2 way point on board 2. Place board 1 on top of board 2 creating a t-shape. Attach board 1. to. board 2 using 2-1/2" pocket hole screws. Step 4: Drill

6' Outdoor Dining Table

Here is a simple and modern outdoor patio table! Bringing the design together took some time, but once I nailed it down it was easy and affordable project.  A huge thank you to National Hardware for sponsoring this post. I used National Hardware's reinforcement hardware to add stability and strength to this build.  As always use safety precautions when building. Measure twice cut once. This post is for entertainment purposes only. Supplies: 12-2x6x8 4 Offset Corner Braces 12 mending plates 1 package 2-1/2" pocket hole screws 2-1/2" wood screws Stain or paint and seal Wood Filler or pocket hole plugs Wood Glue Tools: Table Saw Miter Saw Sander Drill Pockehole jig Nailer (optional) Planer (optional) Before we get to the steps it's important to prep the materials to give it a more modern look. Prep the boards: -Rip 1/8" off each side of the 2x6 lumber. -Rip one-2x6-x8 into 1-1/2" strips to create 3 strips. -Use a planer if desired. -Laminate with glue  two -2x6

45"x45" Square Coffee Table

Hi! Today I'm posting an 45"x45" square coffee table! This is an easy and affordable project that will take 2-4 hours to complete. As always, measure before you cut. Not all wood is created equal so some of the measurements may vary slightly. ALWAYS use safety precautions. This post is for entertainment purposes only. Supplies: 2-1x12x8 4-1x7x8 2-1x2-8 Nails 1-1/4" pockethole (PH) screws Glue Stain, paint or seal. Tools: Miter saw Table saw Circular saw Nailer (optional) Drill Pockethole Jig Clamps Step 1: Cut 1x12x8' // 4 @ 47-7/8" Step 2: Drill PH and glue and plank tabletop together. Step 3: Cut your table top down to 45" to create a square. Do this by clamping a straight edge and using a circular saw. Step 4: Build the base of the table. Start by mitering 1 edge of 2 boards at a 45 degree angle. Step 5: Drill PH leaving a space every 18". Put the 2 mitered edges on the ends. Plank boards to