Skip to main content

45"x45" Square Coffee Table

Hi! Today I'm posting an 45"x45" square coffee table! This is an easy and affordable project that will take 2-4 hours to complete.






As always, measure before you cut. Not all wood is created equal so some of the measurements may vary slightly. ALWAYS use safety precautions. This post is for entertainment purposes only.

Supplies:
2-1x12x8
4-1x7x8
2-1x2-8
Nails
1-1/4" pockethole (PH) screws
Glue
Stain, paint or seal.

Tools:
Miter saw
Table saw
Circular saw
Nailer (optional)
Drill
Pockethole Jig
Clamps

Step 1: Cut 1x12x8' // 4 @ 47-7/8"


Step 2: Drill PH and glue and plank tabletop together.
Step 3: Cut your table top down to 45" to create a square. Do this by clamping a straight edge and using a circular saw.

Step 4: Build the base of the table. Start by mitering 1 edge of 2 boards at a 45 degree angle.

Step 5: Drill PH leaving a space every 18". Put the 2 mitered edges on the ends. Plank boards together using PH screws.

Step 6: Using a straight edge  and a circular saw cut 4 @ 18".


Step 7: Once you have 4 18x29" pieces. Drill PH hole on the top of each board. This is how the base will attach tot the tabletop. Create a box with your 4 boards lining up the mitered edges. I clamped, glued and screwed. I did NOT use metal brackets.
Step 8: Center the base on the tabletop and attach with PH screws.

Step 9: Flip table over. Measure and cut trim. Attach trim to the underneath of the tabletop.

Step 10: Sand, stain and seal your project. I used a mixture of Weathered Oak and Special Walnut.


Thanks for following along! If you take a stab at this project-be sure to post it!! I'd love to see it!

Erin

Comments

  1. You've written a very useful article about t shaped desks. This article provided me with some useful knowledge. Thank you for providing this information. Keep up the good work.

    ReplyDelete
  2. Very well written article. It was an awesome article to read. about coffee table sets Complete rich content and fully informative. I totally Loved it.

    ReplyDelete
  3. It is a proficient article that you have shared here.carved bedroom set I got some different kind of information from your article which I will be sharing with my friends who need this info. Thankful to you for sharing an article like this.

    ReplyDelete
  4. Thanks for such a nice content. Appreciate it :)
    Cheers
    If anyone interested about cutting dry-wood , Have a look link text . thanks

    ReplyDelete

Post a Comment

Popular posts from this blog

6' Outdoor Dining Table

Here is a simple and modern outdoor patio table! Bringing the design together took some time, but once I nailed it down it was easy and affordable project.  A huge thank you to National Hardware for sponsoring this post. I used National Hardware's reinforcement hardware to add stability and strength to this build.  As always use safety precautions when building. Measure twice cut once. This post is for entertainment purposes only. Supplies: 12-2x6x8 4 Offset Corner Braces 12 mending plates 1 package 2-1/2" pocket hole screws 2-1/2" wood screws Stain or paint and seal Wood Filler or pocket hole plugs Wood Glue Tools: Table Saw Miter Saw Sander Drill Pockehole jig Nailer (optional) Planer (optional) Before we get to the steps it's important to prep the materials to give it a more modern look. Prep the boards: -Rip 1/8" off each side of the 2x6 lumber. -Rip one-2x6-x8 into 1-1/2" strips to create 3 strips. -Use a planer if desired. -Laminate with glue  two -2x6

Welcome!

Hi! Thanks for swinging by. I'm Erin, and I'll be posting our building journey on this site. We're new to the building process- so I welcome your feedback and suggestions along the way. I'll be sharing all my SOURCES and general FAQs on this page. Finally, I'm a self-taught DIYer at heart so I'll be sharing tutorials as we furnish our house. Please let me know if you have any questions-I'd love to connect!

$40 Sofa Table

Hi! My sweet children kept jumping over the couch so I needed to do something about the madness!  I decided to build an inexpensive sofa table to attempt to minimize the jumping. Will it work? It's a mystery :) Let's get started! As always, use caution when building, wear safety gear and re-read instructions multiple times. This plan is for entertainment purposes only. Supplies: 3-2x12x8 1-package of 2-1/2" pocket hole screws Finishing supplies: stain, paint, seal Tools: Miter saw Drill Pockethole Jig Table saw (optional) Planer (optional) Step 1: (optional) using a table saw rip 1/8" off each side of the 2x12x8 board. Run boards thru a planer if you have one. Step 2: Using a miter saw cut- 4 @ 28" 1 @ 38" 1 @ 68" Step 3: Build the legs. Drill 1-1/2" pocket holes on boards 1 & 2. Mark the 1/2 way point on board 2. Place board 1 on top of board 2 creating a t-shape. Attach board 1. to. board 2 using 2-1/2" pocket hole screws. Step 4: Drill